Forum Replies Created

Viewing 1 - 6 of 6 posts
  • Alex_S

    Member
    November 2, 2021 at 6:47 pm

    Vielleicht sollte ich auch einen Kondensator dem Dimmer parallel schalten, damit das gepulste PWM-Signal sich glättet und wie eine Gleichspannung “aussieht”.

    Keine Ahnung, was so ein Dimmer für eine Eingangsabtastung hat.

    —-

    Maybe I should also put a capacitor in parallel with the dimmer so that the pulsed PWM signal smooths out and “looks” like a DC voltage.

    No idea what such a dimmer has for input sampling.

  • Alex_S

    Member
    November 2, 2021 at 6:07 pm

    Ich bin dem Problem auf der Spur.

    Ich den PWM-Ausgang an einen Finder-Dimmer angeschlossen. Dort einen 1K-Widerstand parallel.

    Wenn ich das Kabel vom Controllino löse, ist das summen weg.

    (Finder 15.11.8.230.0400)

    —-

    I am getting closer to the problem.

    I connected the PWM output to a Finder dimmer. There a 1K resistor in parallel.

    When I disconnect the cable from the Controllino, the buzzing is gone.

  • Alex_S

    Member
    November 12, 2021 at 11:39 am

    Ich habe die Antwort vom Hersteller “Finder” erhalten. Siehe unten.

    Es geht mit diesem Typ Dimmer nicht.
    Scheint also weder ein Programmfehler zu sein, noch ein Defekt des Controllino.

    —-

    I have received the answer from the manufacturer.

    It does not work with this type dimmer.
    So it seems to be neither a program error, nor a defect of the Controllino.

    —-

    Hallo,

    das 15.11 lässt sich nicht über eine PWM Spannung ansteuern. Dies wird nicht funktionieren!

    Wenn Sie nur eine PWM Spannung zur Verfügung haben, könnten Sie einen extra PWM zu 0…10V Wandler dazwischen schalten.

    Wir hoffen Ihnen hiermit weiter geholfen zu haben.

    Für weitere Fragen stehen wir Ihnen gerne zur Verfügung.

    Mit freundlichen Grüßen aus Trebur-Astheim

  • Alex_S

    Member
    November 8, 2021 at 6:45 pm

    Okay, I wrote to the support of Finder, if there is a trick or a tip, e.g. use a pullup or pulldown resistor.

    Let’s wait and see if they answer me.

  • Alex_S

    Member
    November 8, 2021 at 6:09 pm

    Dear Jarda,
    thank you for your answer.

    I’m sorry, it’s not possible to upload a photo of the dimmer.
    It’s called 15.11.8.230.0400 the manufacturer is Finder.

    https://www.findernet.com/en/worldwide/series/15-series-dimmers/type/type-1511-slave-dimmers/

    There you can find a datasheet. On page 15 there is a wiring diagramm.

    In my opinion, it is a default dimmer, with a 0-10V poti to control the dimmer, it work’s fine.
    I suspect that the dimmer can only handle real 0-10v, and not a PWM signal.

    What else can I test?

    Or is there a bug in my program?

    Should I make the PWM frequency smaller, and maybe a capacitor in parallel to the dimmer input to smooth the signal?

    Alex

  • Alex_S

    Member
    November 2, 2021 at 5:02 pm

    Vielen Dank für eure Antworten.

    Ich hab das Controllino-Modul gegen ein zweites getauscht, und hatte dann das selbe Verhalten.

    D.h. das Controllino selbst muss in Ordnung sein.

    Dann habe ich nach und nach die Kabel an den Inputs getrennt.

    Und, aha, plötzlich funktionierte es.

    Der Fehler war, dass ich ein analoges Signal an einem digitalen Eingang anliegen hatte.

    Keine Ahnung, warum das zu einem Absturz führen kann. War aber so.

    Thank you very much for your answers.

    I exchanged the Controllino module for a second one, and then had the same behavior.

    The Controllino itself must be ok.

    Then I have gradually disconnected the cables at the inputs.

    And, aha, suddenly it worked.

    The error was that I had an analog signal on a digital input.

    No idea why this could cause the hanging up. But it did.

Viewing 1 - 6 of 6 posts