Activity Forums Questions & Troubleshooting Software & Firmware avrdude: stk500_recv(): programmer is not responding Reply To: avrdude: stk500_recv(): programmer is not responding

  • ingmar

    Member
    February 8, 2019 at 3:09 pm

    I might have an similar issue, with Controllino Mini. Please help me asap, as it is used in industrial machine.

    So uploading worked fine, until it suddenly stopped working, with the same error. The controller itself is still running, I can access it through serial monitor through USB cable and send commands – controller is working fine. Just cant upload new program. Tried many different usb ports, com ports, baud rates etc. The same program runs fine on regular arduino uno.

    So it hangs after the line

    Description : Arduino

    and then gives wrong data after

    Hardware Version:

    LOG:

    Quote:


    avrdude: Version 6.3-20171130

    Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/

    Copyright (c) 2007-2014 Joerg Wunsch

    System wide configuration file is “C:Users…hardwaretoolsavr/etc/avrdude.conf”

    Using Port : COM4

    Using Programmer : arduino

    Overriding Baud Rate : 115200

    AVR Part : ATmega328P

    Chip Erase delay : 9000 us

    PAGEL : PD7

    BS2 : PC2

    RESET disposition : dedicated

    RETRY pulse : SCK

    serial program mode : yes

    parallel program mode : yes

    Timeout : 200

    StabDelay : 100

    CmdexeDelay : 25

    SyncLoops : 32

    ByteDelay : 0

    PollIndex : 3

    PollValue : 0x53

    Memory Detail :

    Block Poll Page Polled

    Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack


    —-



    —-



    —-





    eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff

    flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff

    lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00

    hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00

    efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00

    lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00

    calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00

    signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00

    Programmer Type : Arduino

    Description : Arduino

    avrdude: stk500_recv(): programmer is not responding

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x00

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x00

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x00

    Hardware Version: 4744608

    Firmware Version: 0.4611299

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x00

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x00

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x00

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x00

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x00

    Vtarget : 420030.5 V

    Varef : 197193068.8 V

    Oscillator : 0.531 Hz

    SCK period : 17599574.7 us

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x00

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x00

    avrdude: stk500_initialize(): (a) protocol error, expect=0x14, resp=0x00

    avrdude: initialization failed, rc=-1

    Double check connections and try again, or use -F to override

    this check.

    the selected serial port

    does not exist or your board is not connected

    avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x00

    avrdude done. Thank you.